High Performance Thermal CPU Heat Sink Compound Paste, Grease 04, 1.5gm

Description: Normal 0 false false false EN-US X-NONE X-NONE Technical Product BulletinHigh Performance Thermal Epoxy CPU Heat Sink Compound Paste 1.5gm PRODUCT DESCRIPTION: This product is an opaque white heat sink grease compound, which is applied to the base and mounting studs of transistor and diodes to provide a positive heat sink seal, this facilitates heat transfer away from electrical/electronic components and into heat sinks, thereby increasing the overall efficiency and performance of the device.It is a grease like silicone material, heavily filled with efficient heat conductive zinc oxide and a binding agent, this combination promotes high thermal conductivity, high temperature stability, and the lowest amount of bleed and evaporation. This thermal compound resists changes in consistency temperatures up to 180°C; function as heat transfer media, durable dielectric insulation, barrier against environmental contaminants and as a stress-relieving shock and vibration absorbent over a wide temperature and humidity range.This thermal paste is resistant to ozone and ultraviolet degradation and has good chemical and solvent stability, good interference between the heat producing device and the heat transfer media, and low surface tension that enables them to wet most surfaces. This product will not harden, dry, or melt after 1200 hours @ 205°C. POTENTIAL USES: · Effective thermal coupler for any heat sink device, CPU to heat sink · Automotive temperature-sensing devices · Temperature sensors · Applied to the base and mounting studs of transistor, diodes and silicone controlled rectifiers · Power transistors · Diodes, semiconductors · Thermal Joints · For any device where efficient cooling is required · Potting · TEC Modules · Hardware · Telecommunications · Right product for thermal management · High-voltage corona suppressant in connectors for fly back transferors located in TV sets. · Non-Sag or flowing · Non-Hazardous polymerization · Non-Toxic · Non-Corrosive · Reworkable . Easily removed · Non-Flammable · Easy to apply via dispensing or screen printing · Low surface tension that enables it to wet most surfaces, which can lower the thermal contact resistance between the substrate and material. APPLICATION METHODS:Automated or manual dispensing USAGE INSTRUCTIONS:For industrial use only Read MSDS carefully prior to use. STORAGE HANDLING & SHELF LIFE: This product has a shelf life of 5 years at room temperature (76°F) in an unopened container, settlings may occur during long term storage,it is recommended to re-mix the filler by hand or mechanical mixing. Keep container tightly closed store in cool area away fro ignitionsources and oxidizers, no special precautions need to be taken if product is handled according to directions. Shelf life is indicated on theproduct label, any special storage and handling instructions will be printed on the product container label. ELECTRICAL PROPERTIES: Dielectric Strength, volts/mil (ASTM D 150) 390 Dielectric Constant @ 100Hz (ASTM D150) 4.40 Dissipation Factor @ 100Hz (ASTM D150) 0.0021 Volume Resistivity, ohm-cm (ASTM D257) 2.9x1014 THERMAL PROPERTIES: Thermal Conductivity W/m-K 0.88 Operating Temperature Range, °C -60 to 205 Thermal Resistance °C-In2 /W 0.05 Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application TYPICAL PROPERTIES & CHEMICAL CHARACTERISTICS: Color White Base Fluid Dimethyl Polysiloxane Filler Zinc oxide Specific Gravity, 25°C, gm/cc 2.45 Viscosity Paste Press Flow @ 42.5 PSI, 25°C sec 13 Penetration (Worked), mm 2851/10 Evaporation 24 hrs @25°C, % 0.0 Evaporation @ 200°C 24H by weight,% 0.5 Bleed 24 Hours,% 0.6 AVAILABILITY: This epoxy can be supplied in various different packages.

Price: 9.99 USD

Location: Providence, Rhode Island

End Time: 2024-01-21T21:11:19.000Z

Shipping Cost: 0 USD